2021 FORD BRONCO Electrical System Problems

Location of wiring from the factory for Blind Spot Warning and Cross Traffic Alert systems is not protected. The wiring has frayed and broken due to the wiring being unprotected, loose and rubbing on the rear bumper, causing the systems to not function. This is a blatant design defect from the factory, causing two safety systems to fail. Reporting now as, to the best of my knowledge, the manufacturer has not issued a TSB or recall and dealerships have acknowledged the issue.

I was driving on the highway at a speed of approximately 70 miles per hour when the Bronco driver screen gave multiple warning notices and at the same time, the accelerator would not react. Steering power was fine. I was in the second from far left lane on a six lane highway and losing speed quickly. I was able to move to the right and drift to the side of the road without incident. Once stopped, I turned the ignition off and waited a few seconds and then turned it back on again. The error messages all cleared and the Bronco accelerator reacted appropriately. I drove it straight to the dealership for inspection. They found the 210 connector was not making a good connection. They cleaned it and added electric grease and reconnected. Everything cleared and the connection was deemed good. I have not worked in the Bronco engine compartment or had work done that would have resulted in loosening the 210 connector. My understanding from the shop is that corrosion caused this connector to loosen.

I have been getting a message that my blind spot and cross traffic alert deactivated because trailer is attached. I have never had a trailer attached but do have a trailer hitch- the dealer said Ford refuses to pay to have it fixed because the bumper to bumper warranty is out. the car has been garaged and has only 9,000 miles on it. This is a safety issue that I think they should cover as I have no blind spot or cross traffic warnings.

Windows are constantly getting uninitialized so that they don't bump down on opened to allow them to close properly with the frameless doors. This leaves a gap when closed and additionally they will automatically go all the way back down any time they are rolled all the way up. This is very hazardous when driving and needing to close the windows as you're forced to look backwards to see when they get close to the stop and release the button before it hits the top. This was reported to Ford on greater than 10 occasions since I took possession in Jan of 2022, first in March of 20222, and impacts all 4 windows. The dealer can resolve the issue by reinitializing through the computer they can plug into the vehicle and have installed some software updates as well as replaced some of the modules but the issue resurfaces a few days later. Sometimes I am able to resolve using the full reinitialization sequence that they shared with me when I had it there in April of this year but sometimes that fails. Prior to that it would eventually resolve following just a holding up and down of the button for approx. 5 secs at top or bottom. Here is a record of the occurrences with window impacted since I had it in the dealer in April of 2025. 5/2 passenger front (pf), 5/7 drivers back (db), 5/10 db, 5/12 db, 5/15 pf, 5/16 pf, 5/29 pb, 6/13 db, 6/17 pf, db, df, 7/13-7/30 pb, 7/24 db, took to dealer for restarts and software updates 7/30, 8/1 db. I kept a similar record in 2024 4/5 df, 4/6-10 db, 5/7 db, 5/18 pb, 5/22-6/6 pb, 6/6 df, 6/7 pb, 6/9-21 pb, 6/25-27 pb, 6/30-7/8 pb, 7/10-13 pb, 8/1 pb.

Cross traffic and blind spot monitoring/alert failed. Electrical wiring failed due to rubbing on the rear bumper causing failure of blind spot alert and cross traffic alert systems. Reliance on these systems is critical to safe operation of the vehicle.

While driving and completely randomly, multiple critical errors appear on the display, and vehicle goes into limp mode. The errors is play in order as follows: 4x4 Off -Service Vehicle Soon -Service advance Trac -Check 4x4 -Pre-collision assist not available -Service advance track After the errors appear, the vehicle goes into limp mode, no longer being responsive to the accelerator pedal. After putting the vehicle in park and turning it off, then restarting, the vehicle works with no errors. After 5 or so minutes this happens again. It has occured multiple times while driving, placing me in dangerous situation, because once in limp mode, I'm unable to accelerate to the side of the road. By vehicle has been at a Ford dealership for over 8 weeks now. The dealership is able to reproduce this issue. They have done some exploratory repairs by replacing the pedal assembly and throttle body but the problem remains. They're unable to diagnose what is causing the issue. Instead they are denying warranty claims and are replacing the ECM and engine wiring harness at my expense. While this most certainly repair this unknown electrical problem and will get my vehicle safely working, this critical issue will remain under diagnosed.

The front camera is blacked out about 50% of the time when in reverse or when activating the camera system on my Bronco. I have had it into the dealership multiple times for this issue and they continue to tell me there is a over the air (OTA) fix coming soon. The last time they told me this was in Q2 2024 saying that a fix was coming by year end 2024. I am still waiting for this fix and it causes me some distress that I am unable to completely see around my vehicle when parking or in tight spaces. This is separate and distinct from the rear camera issue that was fixed in 2024.

I have a new issue with my Bronco. While it drives well most of the time, I now regularly encounter a problem where multiple error messages pop up on the screen (sequentially) while I am driving, causing the vehicle to effectively, stop responding. The engine remains on, and I don't lose power to the brakes or steering, but the car won't react when I press the gas pedal. It seems like it's some critical failure safety measure, though feels critically unsafe when it occurs. When surrounded by other vehicles, at speed, I am forced to coast to a stop (with a prayer). Usually, when I put it in park, turn off the vehicle, and get out, it will reset all of the errors and work again. This situation is quite dangerous, especially when I'm around other cars. I contacted Ford, but they fit me in for two weeks. Here are the error codes that appear in order: -4x4 Off -Service Vehicle Soon -Service advance Trac -Check 4x4 -Pre-collision assist not available -Service advance track

The contact owns a 2021 Ford Bronco. The contact stated that while driving at an undisclosed speed, the blind spot alert fault message was displayed. The vehicle was taken to the dealer, where it was diagnosed that the wiring module had failed and needed to be replaced. The vehicle was not repaired. The manufacturer was made aware of the failure and referred the contact to the NHTSA Hotline for assistance. The approximate failure mileage was 32,000.

Mileage: 32,000

The contact owns a 2021 Ford Bronco. The contact received notification of NHTSA Campaign Number: 25V315000 (Electrical System); and would like to be removed from the recall distribution list. The local dealer and manufacturer were not contacted.

The contact owns a 2021 Ford Bronco. The contact stated that while driving at an undisclosed speed, the electrical system and the engine seized. The contact noticed fire and smoke which exited from the engine compartment. The contact was the only occupant of the vehicle when the failure occurred. The fire department arrived and extinguished the fire. The vehicle was towed to the dealer. The vehicle was inspected and diagnosed with a faulty alternator. The contact was informed that the seized gears overheated the alternator motor, which caused the fire. The vehicle was repaired. In addition, the failure reoccurred. The contact stated that while driving at an undisclosed speed, the contact noticed smoke exiting the engine compartment. The vehicle was driven to the shoulder of the road. The contact stopped and parked the vehicle. The contact turned the vehicle off. The vehicle was started, however, the vehicle did not start. The contact stated several unknown warning lights were illuminated. The contact stated that when the failure occurred, the contact's wife and minor child were also occupants of the vehicle. The vehicle was towed to the dealer, where it was confirmed to have a failed alternator motor. The contact was informed that the alternator motor needed to be replaced again. In addition, the contact was informed that the seized gears in the alternator motor caused the fire. The vehicle was in the process of being repaired. In addition, the contact stated he was fearful of ever driving the vehicle again. The manufacturer was made aware of the failure. The contact requested a vehicle buyback. The failure mileage was approximately 28,000.

Mileage: 28,000

Car began flashing multiple warnings including power steering, brakes, basically all warnings. Power steering and brakes both failed. Took to dealership. Found wires and wire harnesses burnt and melted. Delaliship says it was due to a pinched wire on an after market winch however the winch was installed in 2022 and never had any issue before. They cited damage underneath on the skid plate which is very minor in nature and should not be able to cause such egregious errors.

2021 FORD BRONCO MILES: 34,247 BOTH REAR CALIPERS ON THE INSIDE "LOCKED" AND CAUSED IRREGULAR PAD WEARING ON THE INSIDE. I AM CONCERNED THE ROOT CAUSE MAY BE A CALIPER ISSUE OR ELECTRONIC BRAKE ISSUE NOT RELEASING THE BRAKE COMPONENTS. REAR OUTSIDE BRAKE PADS AT 80% REAR INSIDE BRAKE PADS AT 2% VEHICLE FIRST LOOKED AT BY A LOCAL MECHANIC 3 WEEKS AGO. FORD DIAGNOSED THE ISSUE TODAY 11/27/24. THERE WAS ONE WARNING 2 WEEKS AGO THAT THE BRAKE WAS FAULTY AND TO CONTACT A DEALERSHIP IMMEDIATELY. THE REAR BRAKES ARE NECESSARY TO SAFETLY STOP THE VEHICLE. I AM CONCERNED THAT I WILL NEED TO CONTINUALLY NEED TO MONITOR THE REAR BRAKE COMPONENTS REGULARLY IN ORDER TO SAFELY OPERATE MY VEHICLE OR THAT THE CALIPERS WILL "STICK" AGAIN CAUSING THE ISSUE TO BE ONGOING. WAY SCARFF FORD CURRENTLY HAS THE VEHICLE AND HAS RECOMMENDED ME TO REPLACE THE REAR CALIPERS, BRAKE PADS AND TURN ROTORS FOR $1100 STATING VEHICLE IS OUT OF WARRANTY BY 3 MONTHS.

The prime screen fails, will not enable any system updates, interconnectivity via bluetooth devices fails...basically everything to do with the primary screen fails. We have documentation to show multiple visits to the dealership that have not been able to fix it. Most recently the dealer has a full screen replacement parts on backorder. They state they have no idea when the backorder will be resolved as they believe the factory will not ship the parts until they are no longer having quality control issues. This has been numerous visits to the deal on the same issue so we need to invoke the lemon law to address this problem.

Four hours into a drive today, going down a fairly steep hill @ ~30mph into a 4 point intersection my Bronco lost all power, brakes and steering. I mean it had nothing. We barely made it thru the intersection because the cars coming directly at us slammed brakes. I had no control and went off the road into someone’s yard, barely missing their fence. It was the scariest thing we’ve ever encountered. My son in the back screaming STOP at the top of his lungs is burned in my brain. What makes all of this worse is that Ford just had it in the shop for 3 days because the week before when they had my Bronco in the shop for yearly inspection/oil change and under their care it had the first symptoms of this issue. I received an app notice of a battery failure AND at their request because of this new issue they wanted my car for a “longer look” the following week. Today was first time driving it since they handed it back to me (I use the valet service that picks up and drops it back to me). Ford could come back and say they will give us a new car and there’s no way I can ever convince my wife to get back in this car. She was absolutely freaked out as the cars coming towards us would have drilled her door. It took Ford 4 hours to come 17 miles to tow us (probably a contractor) to the local Ford dealer that was closed by the time it arrived. We had to Uber to Enterprise and then drive the rental home four hours.

These vehicles have a warning to keep hands on wheels and when on straights it goes off when hands are on the wheel and is annoying you have to rock the wheel back amd forth causing the vehicle to swerve alot of people are saying they have to do the same thing on forums.

my car went from 50 mph to nothing. lost power. coasted to the side of the road barely avoiding traffic. dark road, sheriff had to sit behind car so I was not rear ended in pitch dark had to be towed to the dealer. one week later dealer uncertain. likely complete engine failure maybe fuel valve less than one year old. 11,000 miles

On 2 separate occasions over the past 3 days the vehicle has lost total operability. All functions, lights, locks, etc cease and are unable to simply restart the vehicle. The first occurrence was on a busy highway in poor weather conditions causing a near accident/collision. It appears some electrical malfunction shits off all working of the vehicle only to recover 5-10min later. A brake failure signal was shown on second occurrence. This is a definite life-threatening defect needing prompt investigation and remedy.

We were on vacation in Miami, Florida in February 2022 driving in stop and go traffic when our 2021 Ford Bronco with 2.7L Ecoboost engine suddenly shut down. The entire electrical system shut down and the emergency brake was applied. We were unable to start the vehicle with the ignition button or key fob. Traffic was backing up behind us and we couldn’t put our hazards on to let them know we were having vehicle trouble. A pedestrian tried assisting us with pushing the vehicle but due to the parking brake being applied it wouldn’t move. As a last ditch effort I decided to try to start the vehicle through the Ford Pass app. Thankfully, that worked and the vehicle started. We called a dealership in Miami to see if they could look at the vehicle before we traveled on to Key West. They were unable to get us in so we traveled to Key West. The Ford dealership in Key West was gracious enough to look over the vehicle and errors we received on the Ford Pass app. They did not find anything that would have caused the issue. We were just thankful we were on a side road in stop and go traffic when this happened rather than driving on the highway at 70 mph!

1. Vehicle Issue. -At approximately 2k miles while driving through severe weather in the Rocky Mountains my New Bronco lost ALL electronic driving systems that controlled driving modes including 4 wheel drive modes(GOAT) along with safety systems such as traction control, sensor systems, and cruise control. I was forced to drive through a white out in Rocky Mountains with 2 wheel drive due to the electronic GOAT modes failing. This was a dangerous situation as the systems I was relying on failed me when I needed them most. These systems failed off and on for the next three months before mysteriously subsiding. 2. Attempts to resolve. - Took vehicle to Ford dealer to identify issue and they said there was no record of these failures in the code system which is extremely concerning. If I had gone off the road and injured myself and or died Ford would attempt to say there was no electronic failure when in fact there was a significant electronic failure of ALL traction systems. Fortunately I took video and photo evidence of the electronic failures. Alarmingly, these failures are not being recorded within the vehicle.

The contact owns a 2021 Ford Bronco. The contact stated that when shifting into the park, the front camera sensors would activate when there was no object nearby and there would be a chime. The vehicle was driven to the dealer where it was diagnosed that the front sensors needed to be replaced. The vehicle was not repaired. The manufacturer was notified of the failure. The approximate failure mileage was 200.

Mileage: 200

The Wiper Motor or electrical controlling the Wiper Motor. When the two high wiper blade settings are selected, the wipers run for around 30-40 seconds, then slow down and eventually stop. You can watch it happen. This has happened while having snow and rain on my windshield. In order to get them to start going again full speed you need to turn the switch. I feel this takes my focus off of the road during unfriendly road conditions and puts me and others at risk. The condition has been reproduced by my dealership and I have had my truck to the dealership twice for this problem. The first time they replaced the motor and the second time they said they couldn't fix it. They compared it to another one on the dealers lot and it did the same thing. They said if a bulletin came out on the problem, they would contact me to get it fixed. There were no warning lights. This first happened a couple weeks after picking up my truck new from the dealership. I have a video of it, but cannot attach it. If needed, I can email it to you. Thank you