This Problem Across All Years
Backup camera can fail to start when putting car in reverse. When backup camera does start, it can also suddenly stop during active reversal so that the driver is then reversing with zero visibility. All car audio can stop or suddenly fail to start in the car. This impacts sensors, blind spot warnings, etc. Driver is reliant and conditioned to hearing these sensors for lane keeping, safety, turn signal sounds, etc and without this - driver can dangerously assume there are no issues. Issues have been reproduced and confirmed by dealer, dealer has attempted to fix this and there have been multiple recalls by NHTSA as well - but nothing has fixed this issue yet. No warnings, no messages before any failures.
Backup camera can fail to start when putting car in reverse. When backup camera does start, it can also suddenly stop during active reversal so that the driver is then reversing with zero visibility. All car audio can stop or suddenly fail to start in the car. This impacts sensors, blind spot warnings, etc. Driver is reliant and conditioned to hearing these sensors for lane keeping, safety, turn signal sounds, etc and without this - driver can dangerously assume there are no issues. Issues have been reproduced and confirmed by dealer, dealer has attempted to fix this and there have been multiple recalls by NHTSA as well - but nothing has fixed this issue yet. No warnings, no messages before any failures.
Polestar release version 3.6.4 update that when applied did not inform us that the one pedal drive was set. The vehicle prior to the update was set to 2 pedal meaning when the gas pedal was let go it would coast and slowly come to a stop. The one pedal immediately was enabled which is a safety as I was not aware and the software did not mention it being activated. It nearly caused me to have a safety issue driving home. The backup camera which has been recalled and polestar sent a notice to update the vehicle is still having failures. Polestar has been creating safety hazards with these software pushes without fully testing it.
Polestar release version 3.6.4 update that when applied did not inform us that the one pedal drive was set. The vehicle prior to the update was set to 2 pedal meaning when the gas pedal was let go it would coast and slowly come to a stop. The one pedal immediately was enabled which is a safety as I was not aware and the software did not mention it being activated. It nearly caused me to have a safety issue driving home. The backup camera which has been recalled and polestar sent a notice to update the vehicle is still having failures. Polestar has been creating safety hazards with these software pushes without fully testing it.
Polestar release version 3.6.4 update that when applied did not inform us that the one pedal drive was set. The vehicle prior to the update was set to 2 pedal meaning when the gas pedal was let go it would coast and slowly come to a stop. The one pedal immediately was enabled which is a safety as I was not aware and the software did not mention it being activated. It nearly caused me to have a safety issue driving home. The backup camera which has been recalled and polestar sent a notice to update the vehicle is still having failures. Polestar has been creating safety hazards with these software pushes without fully testing it.
Polestar release version 3.6.4 update that when applied did not inform us that the one pedal drive was set. The vehicle prior to the update was set to 2 pedal meaning when the gas pedal was let go it would coast and slowly come to a stop. The one pedal immediately was enabled which is a safety as I was not aware and the software did not mention it being activated. It nearly caused me to have a safety issue driving home. The backup camera which has been recalled and polestar sent a notice to update the vehicle is still having failures. Polestar has been creating safety hazards with these software pushes without fully testing it.
After the update that should fix the car, it now has several issues. One Pedal Driving doesn't work. When using One Pedal Driving the car should stop when you release the gas. Now the car continues to roll. It is reporting "Brake Failure" and "Collision Detection Failure". Polestar is saying this is normal after the update and it should fix itself in time. Unacceptable, the car has has issues for a year without any updates. Then this is released and makes it work.
After the update that should fix the car, it now has several issues. One Pedal Driving doesn't work. When using One Pedal Driving the car should stop when you release the gas. Now the car continues to roll. It is reporting "Brake Failure" and "Collision Detection Failure". Polestar is saying this is normal after the update and it should fix itself in time. Unacceptable, the car has has issues for a year without any updates. Then this is released and makes it work.
While under light braking in the center lane of the highway at roughly 40MPH and 3-4 car lengths behind the vehicle in front the Automatic Emergency Braking system activated and brought the car to a complete stop. The vehicle behind was several car lengths away and had to slam on their brakes to avoid a collision. The incident caused pain to my right shoulder from the seatbelt tensioning and braking. After coming to a complete stop, the vehicle allowed me to proceed. There were vehicles in neighboring lanes, but at not point was there a situation that would warrant emergency intervention.
While under light braking in the center lane of the highway at roughly 40MPH and 3-4 car lengths behind the vehicle in front the Automatic Emergency Braking system activated and brought the car to a complete stop. The vehicle behind was several car lengths away and had to slam on their brakes to avoid a collision. The incident caused pain to my right shoulder from the seatbelt tensioning and braking. After coming to a complete stop, the vehicle allowed me to proceed. There were vehicles in neighboring lanes, but at not point was there a situation that would warrant emergency intervention.
Vehicle is loosing sound for everything inside the car including turn signals and emergency warnings until infotainment system is restarted. Happens sporadically, usually immediately after getting into the car and multiple people in forums have reported the same issue. Even after multiple OS updates from Polestar, the issue still happens.
Vehicle is loosing sound for everything inside the car including turn signals and emergency warnings until infotainment system is restarted. Happens sporadically, usually immediately after getting into the car and multiple people in forums have reported the same issue. Even after multiple OS updates from Polestar, the issue still happens.
Polestar 2 has a series of software and hardware system failures where the dealership is not logging them asking customers that instead of leaving their car, they can take a look at it right now. The software team is then instructed to reload the 2.2 to 2.4 software as their system is not fully updating causing conflicting software packets leading to dangerous glitches. My specific PS2 has 2.3 software on it and the vehicle lane assistance package drove the car on two occasions into a bike lane. Prior to the the car had a complete system and safety failure where the car accelerated, changed lanes on the freeway to the fast last from the middle lane and then proceeded to flash hardware errors and software errors that disabled all of the safety systems from cameras, blind spot assistance, lane assistance, and more. The vehicle rapidly accelerated on it's own and changed lanes. Polestar took over 3 weeks to get a report that matches the onboard and OTA communications to order a replacement part. It happened again on the bike lane and the vehicle has been with Polestar for 4 months now as are other vehicles and it is happening to other 2022 PS2's with the lane assist and cruise control system (activated or not activated). https://patch.com/california/lakeforest-ca/tesla-crashes-garage-lake-forest-thursday This is very dangerous as when my situation occurred there was no one in the bike lane by the school nor the fast lane on the freeway (both very rare to be empty). The link above (while the link says tesla) it is a polestar of same features less seats and the driver interviewed said that their vehicle rapidly accelerated and changes lanes. Their auto-breaking system and accident avoidance did not stop the vehicle. Errors flashed on the screen and the system crashed. Polestar towed the vehicle and will has not yet provided other information. I have the VIN for that car after speaking to the other party
Polestar 2 has a series of software and hardware system failures where the dealership is not logging them asking customers that instead of leaving their car, they can take a look at it right now. The software team is then instructed to reload the 2.2 to 2.4 software as their system is not fully updating causing conflicting software packets leading to dangerous glitches. My specific PS2 has 2.3 software on it and the vehicle lane assistance package drove the car on two occasions into a bike lane. Prior to the the car had a complete system and safety failure where the car accelerated, changed lanes on the freeway to the fast last from the middle lane and then proceeded to flash hardware errors and software errors that disabled all of the safety systems from cameras, blind spot assistance, lane assistance, and more. The vehicle rapidly accelerated on it's own and changed lanes. Polestar took over 3 weeks to get a report that matches the onboard and OTA communications to order a replacement part. It happened again on the bike lane and the vehicle has been with Polestar for 4 months now as are other vehicles and it is happening to other 2022 PS2's with the lane assist and cruise control system (activated or not activated). https://patch.com/california/lakeforest-ca/tesla-crashes-garage-lake-forest-thursday This is very dangerous as when my situation occurred there was no one in the bike lane by the school nor the fast lane on the freeway (both very rare to be empty). The link above (while the link says tesla) it is a polestar of same features less seats and the driver interviewed said that their vehicle rapidly accelerated and changes lanes. Their auto-breaking system and accident avoidance did not stop the vehicle. Errors flashed on the screen and the system crashed. Polestar towed the vehicle and will has not yet provided other information. I have the VIN for that car after speaking to the other party
On 12/26/2021, I merged onto the I-5 South highway to Irvine, CA, and engaged Pilot Assist. The “speedometer dial” icon turned yellow (as expected), but the “car in front” and “hand hold wheel” icons remained grayed out. I believe this indicated 2 things: (1) the car was still looking for a lead car, and (2) the car was searching for clear lane markings. Everything appeared to be normal at this point as it does take some time to take over the steering. As I approach a slower moving lead car in front of me, I noticed that the car was still at my set speed (~75mph). I get closer and closer to the car in front and the car was not slowing down to match speed and maintain distance. I looked down and still see the same icons: “speedometer dial” icon is yellow (as expected), but the “car in front” and “hand hold wheel” icons were still grayed out. I believe the car didn’t see the car in front. Also, the steering function of the Pilot Assist never engaged. I tried to disengage and re-engage Pilot Assist several times but every time it worked like normal cruise control even when I’m very close to the car in front (~20 feet). I re-confirmed that I have always selected Adaptive Cruise Control in the center screen menu and it’s not a setting that I touched before this incident. I had to disengage Pilot Assist for the rest of the drive. When Pilot Assist is OFF, normally the Lane Keeping Aid icon in the driver display should turn white above 40mph when lane markings are clear. However, the LKA icon remained grayed out for the rest of the drive even when the lane markings are perfectly clear. After the stressful drive, we parked the car for 2 minutes, yet the issues still remained. We reached our destination and parked the car for 30 minutes, and the issues fixed themselves! Both Pilot Assist and LKA started working at the next drive.
On 12/26/2021, I merged onto the I-5 South highway to Irvine, CA, and engaged Pilot Assist. The “speedometer dial” icon turned yellow (as expected), but the “car in front” and “hand hold wheel” icons remained grayed out. I believe this indicated 2 things: (1) the car was still looking for a lead car, and (2) the car was searching for clear lane markings. Everything appeared to be normal at this point as it does take some time to take over the steering. As I approach a slower moving lead car in front of me, I noticed that the car was still at my set speed (~75mph). I get closer and closer to the car in front and the car was not slowing down to match speed and maintain distance. I looked down and still see the same icons: “speedometer dial” icon is yellow (as expected), but the “car in front” and “hand hold wheel” icons were still grayed out. I believe the car didn’t see the car in front. Also, the steering function of the Pilot Assist never engaged. I tried to disengage and re-engage Pilot Assist several times but every time it worked like normal cruise control even when I’m very close to the car in front (~20 feet). I re-confirmed that I have always selected Adaptive Cruise Control in the center screen menu and it’s not a setting that I touched before this incident. I had to disengage Pilot Assist for the rest of the drive. When Pilot Assist is OFF, normally the Lane Keeping Aid icon in the driver display should turn white above 40mph when lane markings are clear. However, the LKA icon remained grayed out for the rest of the drive even when the lane markings are perfectly clear. After the stressful drive, we parked the car for 2 minutes, yet the issues still remained. We reached our destination and parked the car for 30 minutes, and the issues fixed themselves! Both Pilot Assist and LKA started working at the next drive.
Modem failed on vehicle on 02/04/222. Vehicle went in for diagnostic service on that issue on 02/14/2022. Manufacturer installed new software update which added Auto Brake part of Cross Traffic Alert is to stop the vehicle in the shortest possible distance to avoid collision and did not tell me it was added or advise how to disable it. On the morning of 2/15/2022, while using due caution and circumspection, I attempted to back into my flat, level and unobstructed residential driveway. For no reason at all, a loud noise went off and, for no reason at all, this braking system, engaged immediately. I immediately experienced neck pain. The following morning, I pulled straight out of the same driveway and pulled "head first" into my garage. I then went to exit my garage with due caution and circumspection and with no obstacles of any nature behind my vehicle. Again, for no reason at all again, a loud noise went off and, for no reason at all, this braking system, engaged immediately. I again immediately experienced neck pain. The neck pain persisted resulting in my reporting the events to the dealership that morning and eventually the manufacturer that afternoon. I then sought chiropractic diagnosis and treatment. I was diagnosed with having experienced "whiplash" and have been undergoing treatment (at my expense) since 02/15/2022 and still have not fully recovered. Dealership advised me for the first time the afternoon of 2/15/2022 that this new breaking system was installed via a software upgrade on 02/14/2022. Dealership advised me that the new breaking system can be disabled manually on a "drive - by - drive" basis. This is dangerous because the auto must be in reverse gear to activate the time consuming 2 step disable process and operator must remember to disable during every use. Manufacturer advised me today that what I perceive to be a safety defect is "performing as designed" and that it will not be taking any remedial measures of any nature.
Modem failed on vehicle on 02/04/222. Vehicle went in for diagnostic service on that issue on 02/14/2022. Manufacturer installed new software update which added Auto Brake part of Cross Traffic Alert is to stop the vehicle in the shortest possible distance to avoid collision and did not tell me it was added or advise how to disable it. On the morning of 2/15/2022, while using due caution and circumspection, I attempted to back into my flat, level and unobstructed residential driveway. For no reason at all, a loud noise went off and, for no reason at all, this braking system, engaged immediately. I immediately experienced neck pain. The following morning, I pulled straight out of the same driveway and pulled "head first" into my garage. I then went to exit my garage with due caution and circumspection and with no obstacles of any nature behind my vehicle. Again, for no reason at all again, a loud noise went off and, for no reason at all, this braking system, engaged immediately. I again immediately experienced neck pain. The neck pain persisted resulting in my reporting the events to the dealership that morning and eventually the manufacturer that afternoon. I then sought chiropractic diagnosis and treatment. I was diagnosed with having experienced "whiplash" and have been undergoing treatment (at my expense) since 02/15/2022 and still have not fully recovered. Dealership advised me for the first time the afternoon of 2/15/2022 that this new breaking system was installed via a software upgrade on 02/14/2022. Dealership advised me that the new breaking system can be disabled manually on a "drive - by - drive" basis. This is dangerous because the auto must be in reverse gear to activate the time consuming 2 step disable process and operator must remember to disable during every use. Manufacturer advised me today that what I perceive to be a safety defect is "performing as designed" and that it will not be taking any remedial measures of any nature.