2017 RAM 2500 Steering Problems

I am writing to formally demand that Stellantis replace the drag link assembly on my 2017 Ram 2500 at no cost to me. The welding performed during Safety Recall V06 in 2019 has rendered my vehicle unable to receive proper wheel alignment, creating an ongoing safety issue and causing premature tire wear. Background In 2019, my vehicle was brought to dealer to have Safety Recall V06 performed. The recall procedure involved welding the jam nuts to the adjuster sleeve on the drag link. I was not informed at the time that this welding would permanently prevent future alignment adjustments to the drag link. Approximately three months ago, I purchased new tires for my vehicle. When I took my truck to have a wheel alignment performed, I was informed that the alignment cannot be completed because the drag link jam nuts are welded and cannot be adjusted. The alignment is significantly out of specification, causing uneven tire wear and compromised vehicle handling. Current Situation I contacted Hendricks Ram in Cary NC regarding this issue. The dealership has confirmed that: 1.My vehicle cannot be properly aligned due to the welded drag link 2.Ram/Stellantis is refusing to break the welds and replace with the new adjustable drag link kit 3.I am being asked to pay approximately $2,000 out of pocket to correct a problem that was directly caused by Stellantis's recall repair Legal and Regulatory Basis for This Demand October 2023 TSB Update: Stellantis issued revised Technical Service Bulletin instructions for Recall V06 in October 2023 (RCRIT-19V021-0837). This TSB provides that vehicles should be inspected and, depending on conditions found, either have the nuts permanently welded OR the drag link replaced. My vehicle's alignment is out of specification and cannot be corrected—this clearly qualifies for drag link replacement under the revised procedures.

1. Failure to Address a Safety Recall Promptly When scheduling the appointment, I informed the dealership of an open safety recall (Recall V06, NHTSA 19V-021) involving the steering linkage jam nut (a defect which can cause loss of steering control). This recall is critical for safety, yet I was told on the phone that the dealership “could not work on it yet” due to unspecified changes being made by the manufacturer. Upon arrival, I asked again about this recall. The service advisor stated it would require a separate appointment with a “special mechanic” and thus declined to even inspect the vehicle that day. This is extremely disheartening – a known safety defect (announced in January 2019) remains unaddressed on my truck almost seven years later, and the dealership made no effort to expedite or even evaluate the need for repair. As a loyal Dodge customer, I am very concerned that an authorized dealer would postpone a safety recall inspection, leaving me driving a potentially unsafe vehicle. Safety recalls should be handled with urgency, and I urge Dodge to ensure that this recall (V06) is rectified on my truck immediately. It is unacceptable that I must continue driving with a defect that “can result in a loss of steering control… causing a crash without warning,” according to the recall description I found on your site.

The contact owns a 2017 Ram 2500. The contact stated that the vehicle was taken to the local dealer for the recall repair under NHTSA Campaign Number: 19V021000 (Steering). The vehicle was repaired; however, the drag link nut was welded, and the vehicle was unable to be aligned. The contact called the local dealer and was informed that the weld needed to be cut, the vehicle aligned, and then the drag link nut welded again. The vehicle was not diagnosed or repaired. The manufacturer was contacted and referred the contact to the local dealer for assistance. The contact was informed about the reimbursement process for the repair. The failure mileage was unknown.

When I have gone to slow down and try to stop, the vehicle has slide forward a fee times. I thought it was a little weird, but didn't think to much of it. After a while, my transmission started acting up as well. I will be driving down the road about 50-60mph and it will shift to 4th gear and not come out of 4th gear until stopped and shut off and restarted. I recently heard about the recall when I took my truck to the dealership that is close to where I am located at the moment. I decided to research about the recall and what could happen if that part fails. It showed me that if the recalled part fails, it will cause all the problems that is going on with my truck. I am a full-time rv'er and trailer the country pulling an rv everywhere I go. I am stuck where I am until my truck can be fixed of these problems. This is a major setback and a major financial burden to have to stay where I am until it is fixed. I am near Thomson, GA where I am waiting to have my vehicle fixed.

My HCU has failed resulting in loss of traction & locked steering wheel. The truck is not safely operable at this time and dealerships have repeatedly told me they can’t fix it. This has been going on for 2 months.

The contact owns a 2017 Ram 2500. The contact stated that while an employee was driving at undisclosed speeds, there was a whining sound, and vibration coming from the brake pedal. The vehicle was towed to the dealer where it was diagnosed with drained power steering fluid and a hole in the power steering hose. The vehicle was repaired. The manufacturer was not made aware of the failure. The failure mileage was approximately 84,250.

Mileage: 84,250

CONTINUOUS ISSUES WITH ABS LIGHT AND TRACTION CONTROL LIGHT COMING ON, AND STEERING NOT TURNING LEFT AT TIMES.

During a snow storm, ABS and traction control lamps came on. The truck would not come to a controlled stop. After much sliding and skidding it came to a stop by hitting a snow abatement and curb line.

The contact owns a 2017 Ram 2500. The contact stated while driving at undisclosed speeds, the vehicle was not aligned. The steering wheel was upside down. There were no warning lights illuminated. The vehicle was taken to an independent mechanic, who stated they would have to break the welds. The mechanic declined to repair the vehicle. The contact called the local dealer, who stated that they would break the welds and reweld the drag link. The vehicle was not repaired. The manufacturer was contacted, who opened a case and informed her the coverage had expired. The failure mileage was approximately 60,000.

Mileage: 60,000

Service antilock braking system and service electric braking system constantly flashes off and on as if there is a short and all I can do apparently (according to the dealer) is replace the module which is Astronomically priced! Apparently there are a lot of people having this issue. As far as the steering it has been loose since the beginning as there is 2½" of play and everyone blames the steering box but I have invested way to much chasing the problem with no luck.

The steering components are causing it to be difficult keeping the vehicle in the driving lane; the vehicle wanders from side to side. Two seperate Dealers cannot locate the problem.

The contact owns a 2017 Ram 2500. The contact received notification of NHTSA Campaign Number: 19V021000 (Steering). The vehicle was taken to the dealer where the recall was performed. The contact stated that he was informed that the mechanic temporarily welded the nut to the adjuster sleeve and later assembled the drag link welds; however, the contact stated that while driving at various speeds, the vehicle was pulling to the right. The vehicle was taken to several independent mechanics where the contact was informed that an alignment was needed; however, due to the welding, the alignment could not be performed. Additionally, the contact stated that due to the alignment not being performed he had to replace the tires several times. The vehicle was taken back to the dealer where the contact was provided a cost for the repair. The vehicle was not repaired. The manufacturer was notified of the failure and the contact was informed that there would be a charge for any repair on the vehicle. The failure mileage was approximately 98,000.

Mileage: 98,000

Recall for the drag link on this series of 2500 trucks calls for welding an adjustable part of the steering linkage - the drag link jam nuts, rendering that part non-adjustable. Once welded, to then perform an alignment the welds would need to be carefully ground off, alignment work performed, and then once again everything re-torqued and welded back in place per the recall advisory steps. Also consider the effects of welding, grinding, and welding again and again over the life of this HD truck. An alignment is critical to towing thousands of pounds, pulling to the side and overcorrecting while towing a load because a simple alignment is no longer possible is arguably just as dangerous as the original issue attempted to be mitigated (loss of steering). The correct fix for this safety issue is to replace this drag link component, not render the truck unusable. A new drag link without this issue has been engineered and made available for sale, but my VIN says its not eligible for it as a covered recall repair. This is an OEM design failure with a short-sighted workaround that renders the vehicle useless over time; seems ridiculous for the customer to be financially responsible for this failure. Attached photo is of the welded, "recall completed", drag link on my now horribly misaligned truck.

Mopar issued a safety recall for a problem with the jamb nuts on the drag-link becoming loose. I had the recall completed with the expectation that "welding" the adjustable components in place would be a temporary repair until the corrected components were available and then the parts would be replaced. I have made many attempts to contact Mopar to discuss this issue but I haven't been successful. I think welding an adjustable suspension / steering component in place, preventing a re-alignment is ridiculous.

I HAVE COMPLAINED OF THIS TRUCKS STEERING BEFORE. Complaint#11253556. The recall on the DRAG LINK, which effects steering, has NOT been corrected even tho the recall "weld fix" was done. The truck STILL PULLS TO THE RIGHT. I have had 4 wheel alignments. There is NO room for any alignment to be effective. I complained about this problem BEFORE the recall and it NEEDS TO BE FIXED. The dealer has done nothing to help.

I noticed my shifter being very loose and getting harder to put in park. I have always move it very gently so when it started get very loose to the point it feels like it will fall off at any moment I took of the piece of the steering wheel interior to inspect it and have found the shifter bracket is broken which can be very dangerous. I have went out and bought a new one to replace it with for mine and my children's safety.

I am inquiring as to when FCA will provide the consumer with a permanent fix for the current bandaid VO6 Drag Link recall. The idea of welded jam nuts being a “forever fix” seems ridiculous. I understand getting an alignment isn’t something that the average individual is doing on a regular basis however in the event one might modify his/her Ram it must be taken to a Ram dealer in order for the welds to be cut. I feel that this VO6 recall has been in play for long enough that FCA would have by now provided replacement parts that properly/safely fit the effected models so an alignment, and adjustments can be made without the need of breaking welds, and re-welding each time.

Had certified preowned truck aligned after purchase and shop could not adjust front end to stop pull to the right. Took it back to the dealer and they replaced a drag link (but tech said it had nothing to do with the pull) and the second time they rotated front tires left to right. Still pulls to right. Googled problem and I find that it is a common problem with Ram trucks but requires an after market install of ball joints to be able to adjust for the pull. Overheard a service writer who stated “ you can’t align a Ram”.

Reference recall 19V-021. Due to fixing the problem the steering linkage was welded, because it is welded I am unable to get a front end alignment done. So my truck now pulls to the right and there is no way to fix it.

FRONT PASSENGER SIDE UNDERBODY FRAME BOLT & NUT CAME OUT CAUSING LOAD NOISE AND FRAME ENGINE SUPPORT SHIFTED DOWN 25MILS AND FORWARD. OCCURRED IN PARKING LOT 5 MPH GOING OVER SPEED BUMP. REQUESTED DEALERSHIP TO CHECK ALL OTHER UNDERBODY TORQUE SETTING.

Mileage: 66,000

WHILE DRIVING DOWN THE HIGHWAY, ON A RIGHT HAND CORNER I TURNED AND COULD HEAR AND FEEL A 'POP'. THEN HAD SLOP IN THE STEERING, NEARLY CAUSING ME TO CATASTROPHICALLY CRASH . I CONTROLLED IT ENOUGH OFF THE ROADWAY INTO A FIELD AND STOPPED, IF THERE WAS A GUARDRAIL OR DROP OFF, I WOULD HAVE MAJORLY CRASHED. I COULD TURN LEFT, GO STRAIGHT. BUT GOING RIGHT I'D TURN THE WHEEL 1 FULL TURN BEFORE IT 'ENGAGED' STEERING. AFTER INSPECTING THE TRUCK, I NOTICED THE TRACK BAR WOULD MOVE 4-6 INCHES BEFORE THE WHEELS WOULD EVER MOVE. WHEN SHAKING THE WHEEL WHILE PARKED, THE WHEELS WOULD NOT MOVE BUT THE ENTIRE BODY OF THE TRUCK WAS MOVING LIKE CRAZY AS IF IT WERE DANCING. AFTER PULLING THE TRACK BAR OFF THE TRUCK, THE ENTIRE 'HEAD' AROUND THE BEARING ATTACHED TO FRONT PASSENGER SIDE WAS COMPLETELY SHEARED SHEARED ON 1 POINT CAUSING THE BEARING TO HAVE FREE PLAY. THIS TRUCK IS 3 YEARS OLD WITH 57,000 PAVEMENT MILES. CATASTROPHIC FAILURE OF THE STEERING MECHANISM SHOULD NOT HAPPEN AND COULD POTENTIALLY KILL SOMEONE.

Mileage: 57,000

TL* THE CONTACT OWNS A 2017 RAM 2500. THE CONTACT STATED THAT WHILE DRIVING AT VARIOUS SPEEDS, THE STEERING WHEEL SEIZED WITHOUT WARNING AS THE VEHICLE SWERVED TO THE RIGHT. THE CONTACT MANAGED TO GAIN CONTROL OF THE STEERING WHEEL, VEER TO THE SHOULDER OF THE ROAD, SHUT OFF AND RESTART THE VEHICLE BUT THE FAILURE PERSISTED. THE VEHICLE WAS TAKEN TO CARSON DODGE CHRYSLER JEEP RAM (3059 S CARSON ST, CARSON CITY, NV 89701) WHERE IT WAS DIAGNOSED THAT THE DRIVE LINK WAS WELDED AND THE TECHNICIAN CAN NOT ADJUST THE STEERING WHEEL TO THE CONTACTS DESIRE. THE VEHICLE WAS NOT REPAIRED. THE VEHICLE WAS SEEN AT THE SAME DEALER 2 ADDITIONAL TIMES. THE CONTACT MENTIONED NHTSA CAMPAIGN NUMBER: 19V021000 (STEERING) AS A POSSIBLE SOLUTION TO THE FAILURE HOWEVER, THE VIN WAS NOT INCLUDED. THE MANUFACTURER WAS MADE AWARE OF THE FAILURE AND INFORMED THE CONTACT THAT THE RECALL WAS ALREADY COMPLETED AND TO TAKE THE VEHICLE BACK TO THE DEALER. THE FAILURE MILEAGE WAS APPROXIMATELY 71,000.

Mileage: 71,000

WHILE DRIVING MY VEHICLE AT APPROXIMATELY 35 MILES PER HOUR A VEHICLE TURN IN FRONT OF MY VEHICLE AND I DEPRESSED THE BRAKES. THE VEHICLE SHUTDOWN AND WAS ABANDONED IN THE ROADWAY DUE TO LOSS OF POWER. VEHICLES BEHIND ME CONDUCTED EVASIVE MANEUVERS NARROWLY MISSING MY VEHICLE DUE TO THE DEFECTIVE PRODUCT. I WAS ABLE TO DETERMINE THE VEHICLE WAS EQUIPPED WITH A FAULTY FUEL PUMP AND IT HAD BROKEN INTO SEVERAL PIECES INSIDE THE FUEL TANK. THIS ISSUE HAS BEEN DOCUMENTED WITH CHRYSLER; HOWEVER, THEY DO NOT SEE IT AS A SAFETY ISSUE. CLEARLY LOSS OF POWER WHILE OPERATING A VEHICLE ON A BUSY ROADWAY IS A DEFINITE SAFETY ISSUE. THIS ISSUE NEEDS TO BE RECTIFIED BEFORE PEOPLE ARE KILLED OR INJURED. I LOST POWER IN BRAKES AND STEERING.

Mileage: 90,000

DRIVING 2017 DODGE RAM 2500 4X4 ON PAVED RURAL ROADWAY TRAVELING 50MPH WHEN STEERING WHEEL LOST TENSION AND WOULD NOT STEER APPROPRIATELY. VEHICLE BEGAN TO LOSE TRACTION AND CORRECTION WAS NOT POSSIBLE. WHILE WHEN DRIVER ATTEMPTED TO BRAKE, BRAKE PEDAL WAS PRESSED FIRMLY AND DID NOT BRAKE. VEHICLE MAINTAINED SPEED DUE TO BRAKE FAILURE AND STEERING, VEHICLE WENT INTO SIDE SKID FOR 100 YARDS BEFORE HITTING DEEP DITCH AND ROLLING VERTICALLY INTO DITCH LANDING ON WHEELS. ACCIDENT RESULTED IN INJURIES TO BOTH DRIVER AND PASSENGER.

Mileage: 70,000

THE ISSUE IS THE FCA MANDATED DRAG LINK RECALL IN EFFECT FOR MY TRUCK. THE FCA RECALL "FIX" WHICH THEY SAY WAS APPROVED BY YOU, INVOLVES WELDING THE JAMB NUTS TO THE ADJUSTMENT COLLAR ON THE DRAG LINK, WHICH LOCKS THE ENTIRE ASSEMBLY TOGETHER. THE PROBLEM IS THIS FIX ELIMINATES THE ABILITY TO SET THE STEER AHEAD ADJUSTMENT FOR FUTURE WHEEL ALIGNMENTS AND HOW MANY TIMES CAN THE PARTS BE CUT AND WELDED FOR FUTURE WHEEL ALIGNMENTS BEFORE THE DRAG LINK IS NO LONGER ABLE TO BE USED? WE PURCHASED OUR TRUCKS WITH AN ADJUSTABLE DRAG LINK AND THE RECALL THAT FCA STATES YOUR ORGANIZATION APPROVED, ALTERS OUR TRUCKS FROM THEIR ORIGINAL DESIGN AND FORM. THROUGH NO FAULT OF OUR OWN, FCA INSTALLED A DEFECTIVE DRAG LINK ON OUR TRUCKS AND THE ONLY APPROPRIATE REPAIR IS TO REPLACE THE ENTIRE DRAG LINK WITH THE FCA REVISED, ADJUSTABLE DRAG LINK, NOT WELDING STEERING COMPONENTS, WHICH IS NOT APPROVED IN GENERAL TERMS BY THE AUTOMOTIVE INDUSTRY. I HAVE GONE TO FCA AND MY LOCAL DEALER AND BOTH HAVE REFUSED THIS IS ON FCA TO CORRECT. I'M ASKING THE NHTSA TO REQUIRE FCA TO REPLACE MY DEFECTIVE DRAG LINK WITH THE REVISED FCA DRAG LINK AVAILABLE. ALSO I SHOULD NOT BE PENALIZED AND HAVE TO PAY AN EXTRA $250 OUT OF POCKET THAT MY DEALER IS TRYING TO CHARGE ME AS LABOR COST TO UNWELD AND RE WELD THE NUT BACK ON TO DO AN ALIGNMENT WHEN IT'S THE RECALL THAT CAUSED THIS ISSUE AND IS STOPPING ME FROM ROUTINE MAINTENANCE ON MY TRUCK ALSO I DON'T FEEL SAFE WITH THE NUT BEING CUT AND REWELDED AS A SOLUTION OR WELDED PERIOD WHAT HAPPENS IF THE WELD BREAKS THIS IS NOT A PROPER SOLUTION TO THIS ISSUE AND I WOULD ALSO LIKE TO NOT HAVE TO SHELL OUT AN EXTRA $250 ON TOP OF THE PRICE OF AN ALIGNMENT TO HAVE AN ALIGNMENT PREFORMED

Mileage: 32,000

I SENT YOUR ORGANIZATION AN EMAIL REGARDING THIS ISSUE, REQUEST 259479 AND RECEIVED A REPLY . THE ISSUE IS THE FCA MANDATED DRAG LINK RECALL IN EFFECT FOR MY TRUCK. THE FCA RECALL "FIX" WHICH THEY SAY WAS APPROVED BY YOU, INVOLVES WELDING THE JAMB NUTS TO THE ADJUSTMENT COLLAR ON THE DRAG LINK, WHICH LOCKS THE ENTIRE ASSEMBLY TOGETHER. THE PROBLEM IS THIS FIX ELIMINATES THE ABILITY TO SET THE STEER AHEAD ADJUSTMENT FOR FUTURE WHEEL ALIGNMENTS AND HOW MANY TIMES CAN THE PARTS BE CUT AND WELDED FOR FUTURE WHEEL ALIGNMENTS BEFORE THE DRAG LINK IS NO LONGER ABLE TO BE USED? WE PURCHASED OUR TRUCKS WITH AN ADJUSTABLE DRAG LINK AND THE RECALL THAT FCA STATES YOUR ORGANIZATION APPROVED, ALTERS OUR TRUCKS FROM THEIR ORIGINAL DESIGN AND FORM. THROUGH NO FAULT OF OUR OWN, FCA INSTALLED A DEFECTIVE DRAG LINK ON OUR TRUCKS AND THE ONLY APPROPRIATE REPAIR IS TO REPLACE THE ENTIRE DRAG LINK WITH THE FCA REVISED, ADJUSTABLE DRAG LINK, NOT WELDING STEERING COMPONENTS, WHICH IS NOT APPROVED IN GENERAL TERMS BY THE AUTOMOTIVE INDUSTRY. I HAVE GONE TO FCA AND MY LOCAL DEALER AND BOTH HAVE REFUSED TO REPLACE MY DRAG LINK WITH THE REVISED DRAG LINK. I WILL NOT ALLOW THE CURRENT RECALL/FIX TO BE PERFORMED AS AGAIN, IT ALTERS MY TRUCK FROM IT'S ORIGINAL DESIGN AND FORM, NOR WILL I PAY OUT OF POCKET FOR AN AFTERMARKET ADJUSTABLE DRAG LINK, SUCH AS THE ONE AVAILABLE FROM SYNERGY. THIS IS ON FCA TO CORRECT. WHOMEVER AT FCA PROPOSED WELDING THE DRAG LINK ADJUSTMENT COLLAR TO THE LOCK NUTS AND WHOMEVER AT YOUR ORGANIZATION APPROVED IT SHOULD BE IMMEDIATELY FIRED. THE NHTSA SHOULD READ MANY OF THE DISCUSSION THREADS ON RAM FORUM ON THIS SUBJECT AND YOU WILL SEE THE EXTREME DISSATISFACTION OF THE MEMBERS ON THIS ISSUE. I'M ASKING THE NHTSA TO REQUIRE FCA TO REPLACE MY DEFECTIVE DRAG LINK WITH THE REVISED FCA DRAG LINK AVAILABLE. I WILL NOT ALLOW THE CURRENT RECALL.

Mileage: 9,000

THE RECALL ON THE DRAG LINK BY WELDING THE NUTS ON THE ADJUSTMENT BAR IS POOR REPAIR PROCEDURE. CAN'T FIND AN ALIGNMENT SHOP TO UNDO THE WELDS AND CENTER STEERING WHEEL. TOLD THEY WON'T ACCEPT THE LIABILITY

Mileage: 32,000

MY VEHICLE WAS INCLUDED IN SAFETY RECALL V06/NHTSA 19V-021 AND I BELIEVE THE FIX FOR THIS RECALL WAS NOT A SUFFICIENT LONG TERM SOLUTION. THE FIX FOR THIS RECALL WAS WELDING THE NUTS ON THE DRAG LINK. FOR A TEMPORARY FIX THIS IS SUFFICIENT, HOWEVER, FOR A LONG TERM SOLUTION THE PART SHOULD BE REPLACED. WELDING THE NUTS REDUCES THE ABILITY TO UTILIZE NOT RAM/DODGE DEALERS AS COMPANIES DO NOT WANT THE LIABILITY OF CUTTING THE WELDS AND REWARDING THE NUTS IN ORDER TO PERFORM AN ALIGNMENT, WHICH IS NEEDED FOR VEHICLE SAFETY. ADDITIONALLY, GRINDING AND WELDING THE DRAG LINK REMOVES STRUCTURAL INTEGRITY OVER TIME DUE TO METAL BEING LOST AND NEW METAL NOT SITTING FLUSH AS IT SHOULD. THE INABILITY TO UTILIZE NON RAM DEALERS FOR FUTURE REPAIRS DUE TO THE LIABILITY ISSUES WITH GRINDING WELDS AND RE-WELDING COUPLED WITH PREMATURE WEAR AND NON OEM FITMENT WITH FUTURE WELDING/GRINDING MAKE ME BELIEVE RAM MUST REPLACE THE DRAG LINK FOR A LONG TERM SOLUTION.

Mileage: 14,000

TL* THE CONTACT OWNS A 2017 RAM 2500. THE CONTACT HAD THE VEHICLE REPAIRED PER NHTSA CAMPAIGN NUMBER: 19V021000 (STEERING), WHICH REQUIRED A NUT ON THE ADJUSTER SLEEVE. WHILE ATTEMPTING TO HAVE THE WHEELS ALIGNED BY SEVERAL CERTIFIED MECHANICS, THE CONTACT WAS DENIED DUE TO THE WELDING OF THE NUT. THE MANUFACTURER WAS NOTIFIED AND STATED THAT THE VEHICLE NEEDED ALL NEW BALL JOINTS, WHICH WOULD NOT BE COVERED UNDER THE RECALL OR WARRANTY. THE VEHICLE WAS NOT REPAIRED. THE DEALER WAS NOT CONTACTED. THE FAILURE MILEAGE WAS UNKNOWN.

I RECEIVED A SAFETY RECALL NOTICE VIA MAIL. DRAG LINK V06/NHTSA 19V-021. RESPONDED TO DEALER FOR INFORMATION REGARDING REPAIRS. WAS INFORMED THAT THE FIX FOR THIS RECALL IS WELDING THE LOCK NUTS TO THE ADJUSTER SLEEVE. THIS IS NO FIX. THIS IS A FARCE, THIS WILL ELIMINATE THE ABILITY TO ADJUST THE ALIGNMENT IN THE FUTURE. THERE SHOULD BE PARTS REPLACED. NOT WELDED TOGETHER. I DO NOT ACCEPT THE FIX FOR THIS ISSUE.

UNKNOWING LING HAD FCA DEALERSHIP PERFORM RECALL 19V-021, DRAG LINK ASSEMBLY. BY THE DEALERSHIP CONDUCTING THIS IT NOW MAKES MY VEHICLE ILLEGAL FOR TOWING PER THE FEDERAL MOTOR CARRIER SAFETY REGULATION SS 393.209 (D) STEERING SYSTEM. UNIVERSAL JOINTS AND BALL-AND-SOCKET JOINTS SHALL NOT BE WORN, FAULTY OR REPAIRED BY WELDING. THE STEERING GEAR BOX SHALL NOT HAVE LOOSE OR MISSING MOUNTING BOLTS OR CRACKS IN THE GEAR BOX OR MOUNTING BRACKETS. THE PITMAN ARM ON THE STEERING GEAR OUTPUT SHAFT SHALL NOT BE LOOSE. STEERING WHEELS SHALL TURN FREELY THROUGH THE LIMIT OF TRAVEL IN BOTH DIRECTIONS. I HAVE CONTACTED THE FCA DEALERSHIP AND THEY WILL NOT REPLACE THE PART THAT THEY HAVE WELDED THEREFORE MAKING MY VEHICLE ILLEGAL IF INSPECTED.

Mileage: 53,304

RECALL BY MANUFACTURER WELDED STEERING COMPONENTS SO ALIGNMENT CANNOT BE COMPLETED WHEN REQUIRED. NHTSA 11268689

Mileage: 35,000

RECALL - WAS ADVISED WHEEL ALIGNMENT WOULD NO LONGER BE ABLE TO BE DONE DUE TO WELDING ADJUSTING SLEEVES.

RAM WELDED THE DRAG-LINK ASSEMBLY PER A RECALL ON MY 2500. I CANNOT GET ANYONE INCLUDING THE DEALER TO ALIGN MY TRUCK AFTER PUTTING NEW TIRES ON IT. THE FACTORY TIRES WORE UNEVENLY PRIOR TO 30,000 MILES. CHRYSLER SAYS THERE IS NOTHING THEY CAN DO. I SPECIFICALLY ASKED FOR A REPLACEMENT DRAG LINK ASSEMBLY THAT IS NOT WELDED BE SHIPPED TO THE DEALER. THEY ARE REFUSING. I AM IN AWE OF THEIR INABILITY TO RESOLVE AN ISSUE THEY DIRECTLY CREATED. I AM PLANNING ON SUING AS A LAST RESORT.

Mileage: 30,000

NHTSA RECALL19V-021, BY WELDING NUTS ON TO THE STEERING STABILIZER, THIS MAKES THE ISSUE PERMANENT, NO ADJUSTMENT IN THE FUTURE UNLESS REPLACEMENT. THIS IS AN UNACCEPTABLE RECALL FOR THE CONSUMER. FCA NEEDS TO CORRECTS BY INSTALLING AN ADJUSTABLE STEERING STABILIZER

Mileage: 28,000

I BOUGHT THE TRUCK NEW IN OCT. 2017. ALMOST RIGHT AWAY I FELT A PULL TO EITHER DIRECTION WHEN DRIVING BUT IT PULLED STRONGER TO THE RIGHT. I BROUGHT IT BACK TO BROWNS DODGE IN MEDFORD N.Y. AND COMPLAINED AND THEY "SENT IT OUT" FOR A WHEEL ALIGNMENT. I WENT BACK BECAUSE IT WAS STILL PULLING. AFTER A SECOND LOOK BY THE DEALER I WAS TOLD IT WAS DOING WHAT IT SHOULD. IT WASN'T. I THEN TOOK IT TO AN INDEPENDENT PLACE THAT SPECIALIZES IN WHEEL ALIGNMENTS. THEY SAID THEY FIXED IT TOO. THEY DIDN'T. I WAS READY TO GET RID OF THE TRUCK UNTIL I GOT THE RECALL NOTICE. I TOOK IT BACK TO BROWNS AND THEY WELDED THE DRAG LINK AND SAID THERE ARE NO PARTS AVAILABLE AND I WOULD GET A CALL WHEN THEY ARE AVAILABLE. I NEVER RECEIVED A CALL AND I CALLED AND THEY CLAIM THEY STILL DO NOT HAVE THE PART. I NEED MY TRUCK TO DRIVE CORRECTLY. THE DRAG LINK SHOULD NOT BE WELDED. REPLACEMENT IS NEEDED. IT STILL PULLS. I TOW TRAILERS. AFTER THE DRAG LINK WAS WELDED THE "MECHANIC" WROTE ON THE SERVICE FORM HE TEST DROVE IT TO CHECK FOR "TOW". THAT IS A LIE. THE TRUCK NEVER LEFT THE BAY UNTIL IT WAS DONE. I WAS THERE. THE ODO IN AND OUT IS THE SAME TOO. I WAS GETTING HELP FROM FCA BUT NOW THEY WONT HELP EITHER. THEY SAID SOMEONE ELSE WILL BE HANDLING IT AND CONTACTING ME AND NOBODY EVER HAS. THE CASE NUMBER IS 58281442. THANK YOU.

HAD THE RAM 3500 RECAL CORRECTED WITH A SPOT WELD AT THE DON FRANKLIN SOMERSET KENTUCKY DEALER. IT MAY BE APPROVED NHTSA BUT ACCORDING TO DOT OFFICERS IT IS AN ILLEGAL FIX. STATED THAT IT ISNT APPROVEC BY THE FMCSA. IF I AM SHUT DOWN DUE TO TNIS SPOT WELD, I WILL LOOSE REVENUE IN THE THOUSANDS. IF THERE IS A PERMENENT FIX IT NEEDS TO BE DONE ASAP.

Mileage: 192,000

THE RECALL FOR FIXING THE DRAG LINK SEPARATION IS NOT SAFE. YOU DO NOT WELD STEERING COMPONENTS BECAUSE YOU CHANGE THE MOLECULAR STRUCTURE OF THE STEEL MAKING IT HARDER. INSTEAD OF BENDING, IT WILL SNAP. ALSO YOU CANNOT ADJUST TOE IN AND TOE OUT ANY LONGER. THIS IS CREATING A DANGEROUS AND AT BEST A POOR BAND AID FIX THAT IS MAKING A NEW POTENTIAL PROBLEM. CHRYSLER REFUSES TO REPLACE THE PART. NOW, EVERYTIME YOU MEED ALIGNMENTS, THE WELDS NEED KNOCKED OF AMD REWELDED, THUS ALTERING THE COMPONENT ONCE AGAIN. THIS SHOULD BE ILLEGAL.

TL* THE CONTACT OWNS A 2017 RAM 2500. WHILE DRIVING AT ANY SPEED, ATTEMPTING TO PARK THE VEHICLE, OR BACKING OUT OF A PARKED POSITION, THE STEERING LOST POWER. THERE WAS NO WARNING INDICATOR ILLUMINATED. THE VEHICLE WAS TAKEN TO DALLAS DODGE CHRYSLER JEEP RAM (214-327-9361, LOCATED AT 11550 LYNDON B JOHNSON FWY, DALLAS, TX 75238) WHERE IT WAS DETERMINED THAT THERE WAS NO RECALL. THE MANUFACTURER WAS NOT MADE AWARE OF THE FAILURE. THE VEHICLE WAS NOT DIAGNOSED OR REPAIRED. THE FAILURE MILEAGE WAS NOT PROVIDED.

I TOOK MY VEHICLE IN FOR SAFETY RECALL LATE MARCH OR EARLY APRIL. MY CA VEHICKE REGUSTEATION IS DYE 5/31/19. I TRIED TO RENEW ONLINE, BUT TOKD I CANNOT BECAUSE OF A VEHICLE SAFETY RECALL. I CHECKED ONLINE AND THERE IS ONE. IT IS 430 PM, AND THEY XANNOT WORK ON THE TRUCK UNTIL 5/31/19, I HAVE A JOB INTERVIEW AT 1130 AM PST, AND A VETERANS ADMINISTRATION APPT AT 1230 FOR PTSD, BUT IF I DONT GET THE TRUCK FIXED I WILL BE FINED FOR EXPIRED REGISTRATION IN CA. SO, MY CHOICES ARE, SKIP MY NECASSARY PTSD APPT WHEN I AM HAVING CHALLENGES, MISS MY INTERVIEW WHEN I AM UNEMPLOYED, OR GET HUGE FINES FOR EXPIRED REGISTRATION AN CAR INSURANCE CANCELLED. WHAT AM I SUPPOSED TO DO?

THE RECALL FOR FIXING THE DRAG LINK SEPARATION IS NOT SAFE. YOU DO NOT WELD ON STEERING COMPONENTS AS YOU CHANGE THE MOLECULAR STRUCTURE OF THE MATERIAL AND ALSO YOU CANNOT ADJUST TOE IN AND TOE OUT NO LONGER. THIS TO ME IS CREATING A DANGEROUS AND AT BEST A POOR BAND AID FIX THAT IS MAKING A NEW POTENTIAL PROBLEM.

TL* THE CONTACT OWNS A 2017 RAM 2500. THE CONTACT STATED THAT THE VEHICLE WAS INCLUDED IN AN OPEN RECALL REGARDING NHTSA CAMPAIGN NUMBER: 19V021000 (STEERING). BOB MOORE FORD (8948 S I-35 SERVICE RD, OKLAHOMA CITY, OK 73149) AND THE MANUFACTURER STATED THAT THE PARTS WERE UNAVAILABLE. THE MANUFACTURER ALSO STATED THAT THEY WOULD WELD THE DRAG LINK, WHICH THE CONTACT FELT WAS NOT A PROPER REPAIR. THE CONTACT HAD NOT EXPERIENCED A FAILURE. PARTS DISTRIBUTION DISCONNECT.

TL* THE CONTACT OWNS A 2017 RAM 2500. WHILE DRIVING 70 MPH, THE STEERING WHEEL PULLED TO THE LEFT AND THE CONTACT LOST STEERING CONTROL. THE VEHICLE WAS PULLED OVER AND TOWED TO THE CONTACT'S HOME. THE DEALER WAS NOT NOTIFIED. THE CONTACT STATED THAT THE VEHICLE WAS EXPERIENCING THE SAME SYMPTOMS AS LISTED IN NHTSA CAMPAIGN NUMBER: 19V021000 (STEERING). THE MANUFACTURER WAS MADE AWARE OF THE FAILURE. THE VEHICLE WAS NOT DIAGNOSED OR REPAIRED. THE FAILURE MILEAGE WAS 17,800.

Mileage: 17,800

TL* THE CONTACT OWNS A 2017 RAM 2500. WHILE DRIVING AT ANY SPEED, THE STEERING LOST POWER AND WAS DIFFICULT TO TURN. THE DEALER AND MANUFACTURER WERE NOT CONTACTED. THE VEHICLE WAS NOT DIAGNOSED OR REPAIRED. THE FAILURE MILEAGE WAS APPROXIMATELY 10.

Mileage: 10

FRONT TRACK BAR BUSHINGS ARE WORE OUT AFTER LESS THAN 45000 MILES. THE FRONT END MAKES A NOISE AND SHAKES WHEN YOU TURN THE WHEEL. THIS HAPPENS BOTH STOPPED AND AT ANY SPEED.

Mileage: 45,000

WHEN IN MOTION, THE TRUCK WILL SUDDENLY BREAK INTO A VIOLENT "DEATH WOBBLE". IT HAS OCCURRED AT SPEEDS ANYWHERE BETWEEN 40 AND 75 AND NOT ALWAYS WHEN A SLIGHT BUMP IN THE ROAD IT HIT.

Mileage: 17,000

TL* THE CONTACT OWNS A 2017 RAM 2500. WHILE DRIVING VARIOUS SPEEDS, THE VEHICLE BEGAN TO PULL TO THE RIGHT WITHOUT WARNING. THE VEHICLE WAS TAKEN TO A LOCAL DEALER (SOUTH COUNTY RAM IN GILROY 455 AUTOMALL DRIVE, GILROY, CA 95020) WHERE IT WAS DIAGNOSED THAT AN ALIGNMENT WAS NEEDED. THE VEHICLE WAS REPAIRED; HOWEVER, THE FAILURE RECURRED. THE VEHICLE WAS TAKEN TO AN INDEPENDENT MECHANIC WHO DIAGNOSED THAT THE CASTER FAILED AND NEEDED TO BE ADJUSTED OR A BALL JOINT NEEDED TO BE APPLIED. THE DEALER STATED THAT NO KNOWN SOLUTION WAS AVAILABLE. THE FAILURE WAS PERSISTENT. THE CONTACT TOOK THE VEHICLE TO TWO DIFFERENT DEALERS (1. SOUTH COUNTY RAM IN GILROY 455 AUTOMALL DRIVE, GILROY, CA 95020 AND 2. BOARDWALK CHRYSLER DODGE JEEP RAM, 1 BAIR ISLAND ROAD, REDWOOD CITY, CA 94063). THE DIAGNOSTIC RESULTS WERE THE SAME AT BOTH DEALERS. THE MANUFACTURER WAS CONTACTED. THE VIN WAS INVALID. THE FAILURE MILEAGE WAS APPROXIMATELY 326. UPDATED 08/30/17*LJ *CN

Mileage: 326